Skip to main content
Back to Blog

Hobart Undercounter Dishwasher Error Codes (LXn and LXe) Explained

Hobart LXn and LXe undercounter dishwashers show fill, drain, temperature and sensor errors on the display. Here is what each one means according to Hobart's own manuals, and the checks Hobart allows before you call.

NYC Commercial Kitchen Repair4 min read

Most Hobart undercounter errors fall into a few groups: fill errors (water isn't coming in), drain errors (water isn't going out), temperature errors (the booster or tank can't reach temperature, which also matters for sanitizing) and sensor errors. On an LXn, a code like 021 "Drain hose is clogged" or 032 "Fill error, inspect incoming water line" often points to something you can check. A sensor, contactor or over-temperature code needs a technician.

The LXn codes come from Hobart's LXn-Series Customer Support Manual (form 41374, February 2026), which covers LXnC, LXnH, LXnR, LXGnPR and LXGnR and is published on Hobart's warewash site. The LXe messages come from Hobart's LXe Series instruction manual (form 38435, March 2014), which covers LXeC, LXeH, LXePR and LXeR. AM15/AM16 door-type and LXi models aren't covered here.

Hobart LXn error codes

Fill and water level

  • 032: fill error, inspect incoming water line. Booster water level didn't rise within 240 seconds of the fill valve opening.
  • 033: booster fill error, check incoming water line and shut-off valve. The machine switches off.
  • 018: wash tank water level too high, machine draining. The machine tries to pump the excess out. Hobart lists outside water such as a sprayer, an upside-down tub or a detergent feeder, plus drain or fill-valve problems.
  • 035: make sure the tank strainer is locked in place. The message clears when the strainer is sensed.

Drain

  • 021: drain hose is clogged. Clean the drain hose and drain the machine again.
  • 022: drain system error during the wash program.
  • 052: drain system error, check drain pump and hose.

Temperature and heating

  • 003 / 004: booster temperature not reached during fill / wash.
  • 008: wash tank temperature not reached during fill. The fill is aborted.
  • 084: minimum final rinse temperature (120°F) not reached, machine locked. This applies to SCB machines only.
  • 087: minimum final rinse temperature (180°F) not reached after repeating cycles. The wash program locks.
  • 085 / 086: wash tank / booster overtemp tripped. The machine won't run.
  • 088 / 089: wash tank / booster contactor fault. The display says "Pull Circuit Breaker(s) and Contact Service".

Sensors and controls

  • 001 / 002: booster thermistor error (shorted or open).
  • 006 / 007: sump thermistor error (shorted or open).
  • 081 / 082: final rinse thermistor error.
  • 014 / 015: booster pressure error. 016 / 017: wash tank pressure error.
  • 020: rinse system error, check and clean the rinse arms.
  • 038: incoming power too high, machine has powered down.
  • 049: communication between the controls has been interrupted.

Door and chemicals

  • 029: program interrupted, close the door. 039: fill cycle interrupted, close the door.
  • 074 / 075 / 076: detergent / rinse aid / sanitizer empty.
  • 079: sanitizer empty, machine locked until sanitizer is replenished and confirmed.

Hobart LXe display messages

  • DOOR OPEN: the door is open.
  • WASH ARM ALERT: a wash arm is blocked or clogged. Follow the on-screen steps to remove and clean the arm and check the nozzles.
  • LOW RINSE TEMP: low final rinse temperature on the third consecutive cycle. After 10 in a row it changes to "Check Water Input". The machine keeps running.
  • WASH TEMP SENSOR, BOOSTER TEMP SENSOR, RINSE TEMP SENSOR (Service Required): a probe is out of range.
  • FILL ERROR: the unit timed out before filling. The machine won't operate.
  • DRAIN ERROR: drain fault. The machine won't operate and only allows power down.
  • SUMP LEVEL SENSOR / BOOSTER LEVEL SENSOR: a pressure switch is out of range. The machine won't operate.

What's safe to try before calling

These are the checks Hobart's manuals list for operators:

  1. Door codes (029, 039, DOOR OPEN): close the door firmly. If the message keeps coming back, the door switch or spring needs a technician.
  2. Strainer (035): reseat the tank strainer until it locks.
  3. Drain codes (021, 022, 052): Hobart's steps are to make sure the power is off and the wash water has cooled, clear debris from the standpipe and the bottom of the tank, clean the drain hose, then press and hold the power button for 5 seconds to clear the error. The machine drains and powers down. Also check that the drain hose isn't kinked.
  4. Fill codes (032, 033, FILL ERROR): make sure the water supply shut-off valve is open and the supply hose isn't kinked. Hobart recommends 15 to 65 psi flowing pressure.
  5. Rinse or wash arm codes (020, WASH ARM ALERT): remove and clean the arms and nozzles as the screen directs.
  6. Chemical codes (074 to 079): refill or replace the detergent, rinse aid or sanitizer container, then confirm on the touch screen.

When to call a technician

Call if:

  • Any thermistor, pressure-sensor, overtemp or contactor code appears (001, 002, 006, 007, 014 to 017, 081, 082, 085 to 089). For 088 and 089, follow the screen: pull the circuit breaker(s) and call.
  • 084 or 087 locks the machine. A dish machine that can't reach its final rinse temperature isn't sanitizing.
  • 038 (incoming power too high) or 049 (controls not communicating) appears.
  • Drain or fill codes return after you've done the checks above.

Get your dish machine back online

Our technicians repair Hobart and other high-temp and low-temp dish machines and booster heaters across Manhattan and Brooklyn, with 24/7 emergency service, and pricing is confirmed before any work starts. Tell us the model and the code number when you book.

Request service, or see our commercial dishwasher repair and glass washer and booster heater repair pages.

Need Help With This?

Our licensed team is ready to help. Explore our services or request a technician.

Related Articles